Irrigation and water for olives
- 1
Pick the plot first Open a new chat and tap Plots (All) under the question box. Choose the plot you want advice for. ORTH then works from that plot’s crop, variety, soil and documents, and from the farm weather. For olives Pick one plot of one variety. We picked Lote 1: Picual for oil, 2.74 ha of calcareous clay soil with two drip lines per row, 780 single-trunk trees from March 2008 at 7 × 5 m. The fruit is changing colour and the harvest for oil has not started. Every number below is for that plot. - 2
Start from the Irrigation button Pick the plot and tap Irrigation. ORTH offers questions such as this week’s schedule, a water-quality check, or turning the water requirement into runtime for your system. Tap one to ask it. For olives On Lote 1 the yearly water allowance is smaller than what the trees could use. So the question is less how much the crop needs and more where a limited amount does the most good. - 3
Ask for this week’s schedule We tapped Build this week’s irrigation schedule for this plot. ORTH’s answer for 12 to 18 November: keep the drip off, with no irrigation events, no runtime and no volume. The table gives the reason day by day. Rain is forecast on every day, up to 9.2 mm on 18 November, while ET₀ stays between 1.3 and 2 mm a day and the surface soil is already moist. On clay soil just before the oil harvest, the aim is air for the roots and sound fruit, and replacing ET₀ in full is not the goal. On 15 and 16 November, check under a few drippers and in the low areas: if the soil is sticky or leaves water on the spade, the system stays off. After the rain of 18 November, check the root zone again, and do not restart only because the surface looks dry. - 4
Spread a limited allowance over the stages We told ORTH the allowance is 1,500 m³ per hectare per year and asked for a plan from flowering to harvest. ORTH read it as 150 mm for the season, which is 4,110 m³ on Lote 1, and as an envelope to spend by stage instead of a fixed calendar. Flowering to fruit set gets 30 mm: no sharp stress, and if the clay still holds winter moisture the water is carried forward. Early fruit growth gets 25 mm. Pit hardening is the main saving window with 15 mm, enough to avoid severe stress and shrivelled fruit. From the end of pit hardening through oil accumulation comes the largest share, 65 mm, given back step by step. The last 15 mm are a reserve for heat before harvest. After fruit set, look at the crop load again: a light crop does not need the full amount. - 5
Give the drip layout, get hours We gave the layout: two drip lines per row, 4 L/h emitters every 1 m, rows 7 m apart and trees 5 m apart. ORTH worked out the application rate: 2 lines times 4 L/h, divided by 7 m times 1 m, gives 1.143 mm per hour. So 1 mm takes 52.5 minutes, is 27.4 m³ on Lote 1 and 35 L per tree. An irrigation of 4 mm runs 3.5 hours and one of 6 mm runs 5.25 hours. On this clay ORTH starts with events of 4 to 6 mm, and splits an event if water ponds or runs out of the wetted strip. The whole 150 mm comes to about 131 hours. These hours assume that every emitter really gives 4 L/h. Measure the flow of a set of emitters, then correct: the hours times 4, divided by the measured average flow in L/h. - 6
What changes for table olives With the same 1,500 m³ per hectare, ORTH moves water forward for table olives, toward fruit growth and size. Flowering to fruit set keeps 30 mm. Early fruit growth, when the cells divide and size is set, rises to 40 mm and has the highest priority. Pit hardening gets 25 mm, a moderate deficit only, because long stress costs size. Flesh growth up to the green harvest gets 45 mm, and 10 mm stay in reserve. The moisture is kept steadier, without a hard dry-down followed by a heavy irrigation. In a dry year with a heavy crop, 150 mm may not be enough for the top sizes, and then the crop load matters more than in oil olives. The reserve is for preventing stress; a large irrigation right before picking to swell the fruit is not what it is for.
1.
2.
3.
4.